RESIDENTIAL HVAC · DUBLIN, CA

Residential HVAC & Heat Pumps in Dublin, CA

Dublin’s newer homes are tight, often over-equipped, and short on mechanical space. We run the load calculation first, then fit a heat pump that actually suits the house, the attic and the lot.

Remodels · Retrofits · Heat Pumps · Multi-Zone Systems

Project Inquiry

Plan your Dublin project

Share your project type, ZIP, timeline, and how to reach you. We will follow up.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

  • 5.0 Google Rating 5.0 out of 5 stars
  • Mitsubishi Electric Diamond Contractor
  • C-20 + C-36 Licensed & Bonded
  • Serving the Bay Area since 2015

Example from Berkeley

Whole-home heat pump remodel

View project →
Mitsubishi wall unit in a Berkeley remodel by 3rdGen
Mitsubishi wall unit in a Berkeley remodel by 3rdGen
Mitsubishi hanging outdoor units in a Berkeley remodel by 3rdGen

High-end residential remodel

Hearst Remodel

A published Berkeley remodel using a six-zone ductless heat pump. It is not a Dublin project, but it shows how we plan indoor and outdoor placement and coordinate with a general contractor.

Home type
Existing home, remodel for sale
System
Fujitsu multi-zone ductless heat pump
Mechanical scope
  • · Six indoor wall units
  • · Two outdoor units
  • · Wall-mounted outdoor brackets
  • · Refrigerant routing and field coordination

Challenge

  • Existing older home with limited equipment placement options
  • Outdoor units required side-yard wall bracket mounting
  • Finish-sensitive interior installation
  • Coordination with the general contractor’s remodel schedule

3RDGEN scope

  • Six-zone ductless heat pump installation
  • GC-led remodel coordination
  • Permit and inspection support
  • Startup as part of the completed remodel scope

Outcome

The six-zone Fujitsu ductless system was installed, permitted, inspected, and completed as part of the home’s remodel-for-sale scope — delivering zoned heating and cooling without a conventional ducted retrofit.

Representative example from a Berkeley, CA remodel, not a project in this city. Photos and full details on the project page.

View project

Local projects

Heat pump & HVAC installs for Dublin homes

Recent installs by the 3rdGen crew that serves Dublin: ducted and ductless heat pumps, air handlers and ductwork.

Outdoor heat pump condenser unit installed in a garden bed beside a wooden fence
Horizontal air handler hung in a crawlspace with insulated ductwork and a drain line
Outdoor heat pump condenser mounted beside a louvered vent on the side of a house
Outdoor heat pump condenser mounted on an exterior wall above landscaped planting
Two outdoor condensers on wall brackets with a white line-set cover running down the stucco wall
Sheet-metal plenum and insulated round duct above a furnace in a utility closet

Newer houses, tighter spaces

Dublin’s housing is young, which changes how we size and place equipment

Much of Dublin was built in recent decades under modern energy codes. Those homes lose less heat than older ones, so a system sized by square footage tends to be bigger than the house needs.

The other recurring challenge is space. Attics are tight, mechanical closets are small and side yards are narrow. We check clearances early so the equipment we specify is something that can be installed and serviced.

Where a house or condo was built with a single-speed system, a variable-speed heat pump is a natural fit for Dublin’s warm afternoons and cooler evenings.

  • Daily temperature swing

    Hot afternoons and cooler nights favor inverter equipment that can ramp up and idle down.

  • Tight attic runs

    Limited attic space calls for duct layouts with gentle bends and short runs rather than long flex.

  • Small mechanical closets

    We confirm that the selected air handler fits, with room for filter and coil service.

  • Attached homes

    Townhomes and condos limit outdoor-unit placement and often require association approval.

Dublin, CA HVAC

In Dublin, most of the housing is newer, and so are the mistakes

Dublin grew fast, with large newer subdivisions, townhome and condo communities, and a smaller core of older ranch houses. In the newer homes, the systems are often sized generously and the ducts squeezed into tight attics and soffits. Our job is usually to make the equipment fit the real load and the real space.

Design climate · Title 24 Climate Zone 12
Winter design temp
32°F
Summer design temp
90°F

ACCA lists Dublin at 32°F for heating and 90°F for cooling at 1%. Afternoon heat is real and summer days swing widely, with a daily range around 35°F in the data. That favors inverter-driven heat pumps that can ramp up for the afternoon and idle through the evening.

ACCA Manual J design data · Dublin, CA (ACCA micro-climate)

The Dublin housing mix

A large share of Dublin’s homes went up in the last few decades. Many are two-story houses with systems in the attic, tight mechanical closets and small side yards. Equipment is easy to specify and hard to fit, so we verify clearances and service access on paper before ordering.

Townhomes and condos are common. Space for outdoor units can be limited to a patio, a roof or a shared pad, and association approval is usually part of the process.

The older ranch-style houses near the original town center have a different profile: single-story, often with slab or crawlspace construction and duct systems that were added or modified over the years.

Manual J for modern construction

Houses built to recent energy codes have better envelopes than their age suggests. We use real window and insulation data rather than defaults, and the result is often a smaller system than the one on the pad.

Manual S and the afternoon peak

With big daily swings, we look at capacity at the 90°F design point and at part-load efficiency, then pick equipment that does both without oversizing.

Manual D for tight attics

Attic space in many newer houses is limited. We design duct runs that avoid sharp bends and long flex, and place returns where they actually pull air.

Access and service clearance

A system you cannot reach is a system that will not get maintained. We check that filters, coils and condensate lines can be serviced in the space provided.

Dublin permits, power and rebates

HVAC permits in Dublin come through the City of Dublin’s Building and Safety division. We prepare the load calculation, equipment schedule and outdoor-unit location for the submittal. HOA or master-association approval may be needed in addition.

Dublin is served by PG&E for delivery, with Ava Community Energy as the default generation provider. Incentives such as TECH Clean California, BayREN and utility offers change throughout the year. We review current programs while scoping and never assume a rebate amount.

Dublin and nearby

Dublin, along with Pleasanton, San Ramon, Livermore and the rest of the Tri-Valley.

Homeowner reviews

Trusted by Bay Area Homeowners

5.0
5 out of 5 stars from 207 Google reviews

207 Google reviews

  • Mitsubishi Electric outdoor heat pump installed on a concrete pad at a Bay Area home Expand
    Mitsubishi mini-split installed with outstanding care. Indoor and outdoor units done right. High efficiency meant a meaningful federal tax credit too.
    Gary Marks Google review
  • Mitsubishi Electric Smart Multi outdoor unit wall-mounted on a residential exterior Expand
    Devin and his crew did a fantastic job installing AC for our whole house. High quality Mitsubishi equipment and a clean installation throughout.
    Christian Vuerings Google review
  • Mitsubishi Electric air handler installed in an insulated attic with sealed duct connections Expand
    Devin is meticulous, methodical, and knowledgeable. Professional crew and a heat pump install we trust completely.
    D C Google review

Photos from the installs above

Read all 207 reviews

Project steps

How a Dublin retrofit goes from call to commissioning

Newer homes reward careful design. Most of the work happens before we show up with tools.

01 — Intake and photos

Year built, existing system, attic and closet photos, and what the home currently does wrong.

02 — Manual J

A load calculation that uses the glass, insulation and orientation the house really has.

03 — Equipment and ducts

Manual S picks equipment for the afternoon peak. Manual D lays out supply and return paths that fit the attic.

04 — Permit and association

Submittal to Dublin Building and Safety, plus any HOA package for the outdoor unit.

05 — Install

Old equipment removed, new equipment set, ducts, line sets, drain and electrical completed.

06 — Commissioning

Airflow, charge and controls tested and documented before the final inspection.

Done properly

What to expect on a Dublin job

Dublin retrofits tend to be quick when the design is settled first. The time goes into the planning, not the install.

We verify every system we install before the permit is signed off.

Tell us about the project
  • Fit check

    Clearances and service access confirmed against the equipment chosen.

  • Ducts and returns

    Attic runs rebuilt to the Manual D where needed.

  • Electrical and condensate

    Circuit, disconnect and drain routed to code.

  • Verification

    Charge and airflow tested, then controls demonstrated.

Cost

What affects the cost of a heat pump in a Dublin home

For newer Dublin houses, price differences come mainly from how much duct work the attic needs, how far the line set must run, electrical capacity and whether a condo or HOA limits where equipment can go. Equipment size often goes down once the load is calculated.

Ducted heat pump, existing ducts usable $20k–$30k Equipment tier, capacity, controls, condenser location and access
Ducted heat pump + duct repair or resizing $25k–$45k Amount of ductwork replaced, crawlspace or attic access, return-air changes
Ductless multi-zone, 3–4 heads $25k–$40k Head type, line-set length, routing, concealment and finish conditions
Whole-home ducted + ductless combination $40k–$80k+ Multiple systems, zoning, ductwork, filtration, ventilation and architectural coordination
New construction system $20k–$50k+ Building size, system count, Title 24/design requirements and coordination with the build
ADU system $10k–$15k Zone count, head type, line-set routing, and whether the ADU shares the main house or stands alone
Electrical panel upgrade, when required $10k+ Service size, meter location, utility requirements and site conditions

Prices as of November 2026. Complex whole-home and design-build projects can exceed these ranges. Rebates and incentives may reduce your net project cost.

Ask us

Got a Dublin home project?

Send the approximate build year, current equipment and any photos of the attic or closet. We will tell you what we would calculate and how we would approach it.

  • Reviewed by a project lead, not a dispatcher
  • We tell you if your scope is not a fit for us
  • No high-pressure in-home sales appointment

Project Inquiry

Send your project details

Project type, ZIP, timeline, and how to reach you.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Mitsubishi Electric

Proud Mitsubishi Electric Diamond Contractor

As a Mitsubishi Electric Diamond Contractor, we design and install ducted, ductless, and multi-zone systems for Bay Area homes, with factory-trained crews and longer warranty options on qualifying residential installs.

Mitsubishi is not automatically the answer to every home. We start with what the project requires and recommend the system that makes sense.

Mitsubishi Electric H2i hyper-heat outdoor heat pump units
Mitsubishi Electric Heating and Air Conditioning Mitsubishi Electric Diamond Contractor

12 Year Parts &
Compressor Warranty

12-year warranty

Extended parts & compressor coverage on qualifying Diamond installations.

Factory-trained crews

Ongoing manufacturer training on the latest hyper-heat systems.

Priority support

Direct factory escalation if anything ever needs attention.

FAQ

Common Questions

Short answers for Dublin homeowners and builders.

My Dublin house is only about ten years old. Is a heat pump worth it?

It can be, especially if the existing system is a single-speed AC and gas furnace. A heat pump handles both heating and cooling, and a Manual J shows whether the current system is the right size.

Why might my new house need a smaller system?

Modern codes bring better windows and insulation, so cooling and heating loads are lower than for older houses of the same size. Rule-of-thumb sizing overshoots.

Will it fit in my small attic or closet?

We check that before quoting. If a standard air handler will not fit, there are low-profile and ductless options, and we confirm service clearances up front.

Can I install a heat pump in my Dublin townhome?

Usually, but the outdoor unit location is the deciding factor, and your association may require approval. We help prepare the package.

Do I need a permit in Dublin?

Yes. Dublin Building and Safety issues mechanical permits. We handle the submittal and inspections.

Is Ava Community Energy my provider?

Yes, by default. Ava supplies generation and PG&E delivers it. Rebates such as TECH Clean California and BayREN change, so we check what applies when we scope your project.

Can you design HVAC for a new custom home in Dublin?

Yes. We deliver Manual J, S and D documents and coordinate equipment locations with your builder or architect before framing.

Still have a question?

Tell us about your Dublin project

Discuss Your Project

Project Inquiry

Ready to Talk Through Your Dublin Project?

Tell us what you’re planning. We’ll review the project and follow up with the appropriate next step.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Project category
Project type
Timeline