RESIDENTIAL HVAC · NEWARK, CA

Residential HVAC & Heat Pumps in Newark, CA

Newark is a flat, compact city of single-family tracts, townhome communities and newer infill near the bay. The usual job here is an aging furnace and AC, a hot second floor, or a garage that needs conditioning.

Remodels · Retrofits · Heat Pumps · Multi-Zone Systems

Project Inquiry

Plan your Newark project

Share your project type, ZIP, timeline, and how to reach you. We will follow up.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

  • 5.0 Google Rating 5.0 out of 5 stars
  • Mitsubishi Electric Diamond Contractor
  • C-20 + C-36 Licensed & Bonded
  • Serving the Bay Area since 2015

Example project from the East Bay

Whole-home heat pump remodel

View project →
Mitsubishi wall unit in a Berkeley remodel by 3rdGen
Mitsubishi wall unit in a Berkeley remodel by 3rdGen
Mitsubishi hanging outdoor units in a Berkeley remodel by 3rdGen

High-end residential remodel

Hearst Remodel

A multi-zone remodel we did in Berkeley, shown here as a sample of our work. It is not a Newark project, but it shows how we plan and install a complete heat pump system.

Home type
Existing home, remodel for sale
System
Fujitsu multi-zone ductless heat pump
Mechanical scope
  • · Six indoor wall units
  • · Two outdoor units
  • · Wall-mounted outdoor brackets
  • · Refrigerant routing and field coordination

Challenge

  • Existing older home with limited equipment placement options
  • Outdoor units required side-yard wall bracket mounting
  • Finish-sensitive interior installation
  • Coordination with the general contractor’s remodel schedule

3RDGEN scope

  • Six-zone ductless heat pump installation
  • GC-led remodel coordination
  • Permit and inspection support
  • Startup as part of the completed remodel scope

Outcome

The six-zone Fujitsu ductless system was installed, permitted, inspected, and completed as part of the home’s remodel-for-sale scope — delivering zoned heating and cooling without a conventional ducted retrofit.

Representative example from a Berkeley, CA remodel, not a project in this city. Photos and full details on the project page.

View project

Local projects

Heat pump & HVAC installs for Newark homes

Recent installs by the 3rdGen crew that serves Newark: ducted and ductless heat pumps, air handlers and ductwork.

Wall-mounted ductless indoor unit above a seating area in a finished living room
Large two-fan heat pump condenser on a gray pad against house siding
Mitsubishi heat pump outdoor unit with two fans installed on a concrete pad beside a house
Residential outdoor condenser unit on a pad beside a stucco wall with landscaping
White ductless heat pump outdoor unit mounted on steel rails on a roof deck
Large two-fan heat pump outdoor condenser standing on a pad beside a house

Flat lots, ducted attics

Newark homes are well suited to a ducted heat pump, if the ducts are right

Newark was largely built out as suburban housing, and many homes have a similar layout: single or two story, attic duct runs, a hall closet or garage for the furnace. That makes equipment placement predictable.

What varies is the condition of the ducts and the size of the old system. A furnace and AC sized by rule of thumb decades ago is often bigger than the house needs, which affects comfort and noise.

Newark is in Alameda County, and heat pump permits are handled by the City of Newark’s building division.

  • Attic duct runs

    Hot attics make poorly insulated ducts lose a lot of capacity. We check insulation and leakage and recommend repairs that matter.

  • Garage air handlers

    A garage location is common. It needs the right clearances, combustion air rules for any remaining gas appliances, and a condensate path.

  • Warm afternoons

    Newark’s design cooling temperature is in the mid 80s, so shade, glass and attic insulation all feed into the sizing.

  • Close neighbors

    Side yards on tract lots are narrow. We choose condenser locations and models with sound and distance in mind.

HVAC design in Newark

Newark’s tract homes have predictable layouts, but the old systems are rarely sized right

Newark is a compact city on the south end of the Alameda County bayfront. Most homes are suburban houses and townhomes on level lots, with attic duct systems and a furnace tucked in a closet or garage. The layout is easy to work with. The old equipment is usually the problem, often oversized and paired with leaky ducts.

Design climate · Title 24 Climate Zone 3
Winter design temp
36°F
Summer design temp
86°F

Design temperatures are 36°F for heating and 86°F for cooling. A daily range near 24 degrees means warm afternoons and cool nights. That calls for equipment that can deliver real cooling and also run gently on mild days.

ACCA Manual J design data · Newark (micro-climate)

Typical Newark housing

Newark’s growth came mostly in the later 20th century, so many homes are single or two story tract houses with slab or raised foundations. Ducts usually run through the attic, and the furnace and AC are a split pair from the same era.

Townhome and condo communities add attached units where outdoor space is limited and HOA rules may govern where a condenser can go.

Newer infill homes are built to current energy code with better envelopes. Their loads are lower, so equipment choices skew smaller.

Right-sizing against an oversized old system

Older systems were often sized by rule of thumb and can be bigger than the house needs. Manual J gives us a number we can defend. Oversized equipment cycles often, wastes energy and leaves some rooms uneven.

Duct testing before reuse

Attic ducts are exposed to summer heat and often leak. We test or inspect them and use Manual D to decide whether to repair, partly rebuild or replace.

Garage and closet air handlers

Where the indoor unit sits matters for service access, drain routing and fire rules around gas appliances. We confirm the spot before we select the model.

Townhome sound and clearance

Attached homes need condenser locations that meet clearance and neighbor sound expectations. We review the site plan and HOA requirements first.

Permits, power and rebates in Newark

The City of Newark’s building division issues the permits for heat pump installs. The application typically includes the load calculation, equipment data and the location of the outdoor unit. We handle submittal and inspection scheduling.

PG&E delivers electricity in Newark, and Ava Community Energy is the default generation provider. State and regional incentive programs for heat pumps, including TECH Clean California and BayREN, open and close and have conditions. We check what applies when we scope your job.

Where we work around Newark

Residential neighborhoods across Newark, plus neighboring Fremont, Union City, Hayward and Milpitas.

Homeowner reviews

Trusted by Bay Area Homeowners

5.0
5 out of 5 stars from 207 Google reviews

207 Google reviews

  • Mitsubishi Electric outdoor heat pump installed on a concrete pad at a Bay Area home Expand
    Mitsubishi mini-split installed with outstanding care. Indoor and outdoor units done right. High efficiency meant a meaningful federal tax credit too.
    Gary Marks Google review
  • Mitsubishi Electric Smart Multi outdoor unit wall-mounted on a residential exterior Expand
    Devin and his crew did a fantastic job installing AC for our whole house. High quality Mitsubishi equipment and a clean installation throughout.
    Christian Vuerings Google review
  • Mitsubishi Electric air handler installed in an insulated attic with sealed duct connections Expand
    Devin is meticulous, methodical, and knowledgeable. Professional crew and a heat pump install we trust completely.
    D C Google review

Photos from the installs above

Read all 207 reviews

Our process

A straightforward path for a Newark install

Because many Newark homes share a layout, we can move quickly through each step, but we still measure each house on its own.

01 — Visit and inspect

We check the attic, garage or closet space, existing ducts, thermostat location and panel.

02 — Run the Manual J

Room loads are calculated using the house’s actual windows, insulation and orientation, with Newark’s design temperatures.

03 — Select with Manual S

A unit is chosen to match the calculated loads, avoiding the oversizing common in older installs.

04 — Design ducts with Manual D and pull the permit

Trunk and branch sizes, returns and register locations are worked out, then we submit the permit.

05 — Install the system

Equipment is set, ducts are sealed, the circuit is run and the drain is connected.

06 — Verify and explain

We test airflow and refrigerant charge, pass inspection and teach you the controls.

What is included

The finished scope of a Newark attic-duct swap

Replacing the pair of old units is the visible part. Behind it are duct repairs, a new circuit, a drain, and a sealed penetration where lines pass through.

We close out with testing and a walkthrough.

Tell us about the project
  • Equipment swap

    Old furnace, coil and condenser removed, new heat pump set.

  • Duct repairs

    Leaks sealed, returns improved, weak branches replaced.

  • Circuit and drain

    Electrical connection and condensate drain completed to code.

  • Test and train

    Airflow, charge and controls verified, then explained to you.

Cost

Why two Newark heat pump quotes can look very different

Duct repairs, equipment size, the number of zones, location of the air handler and electrical work vary from house to house. A clean swap in an accessible attic is a smaller scope than a conversion that adds zones or reworks the ducts.

Ducted heat pump, existing ducts usable $20k–$30k Equipment tier, capacity, controls, condenser location and access
Ducted heat pump + duct repair or resizing $25k–$45k Amount of ductwork replaced, crawlspace or attic access, return-air changes
Ductless multi-zone, 3–4 heads $25k–$40k Head type, line-set length, routing, concealment and finish conditions
Whole-home ducted + ductless combination $40k–$80k+ Multiple systems, zoning, ductwork, filtration, ventilation and architectural coordination
New construction system $20k–$50k+ Building size, system count, Title 24/design requirements and coordination with the build
ADU system $10k–$15k Zone count, head type, line-set routing, and whether the ADU shares the main house or stands alone
Electrical panel upgrade, when required $10k+ Service size, meter location, utility requirements and site conditions

Prices as of November 2026. Complex whole-home and design-build projects can exceed these ranges. Rebates and incentives may reduce your net project cost.

Project inquiry

Planning HVAC work in Newark?

Send us the basics: age of the home, what you have now, and what you want to fix. Photos of the attic or garage utility space help.

  • Reviewed by a project lead, not a dispatcher
  • We tell you if your scope is not a fit for us
  • No high-pressure in-home sales appointment

Project Inquiry

Send your project details

Project type, ZIP, timeline, and how to reach you.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Mitsubishi Electric

Proud Mitsubishi Electric Diamond Contractor

As a Mitsubishi Electric Diamond Contractor, we design and install ducted, ductless, and multi-zone systems for Bay Area homes, with factory-trained crews and longer warranty options on qualifying residential installs.

Mitsubishi is not automatically the answer to every home. We start with what the project requires and recommend the system that makes sense.

Mitsubishi Electric H2i hyper-heat outdoor heat pump units
Mitsubishi Electric Heating and Air Conditioning Mitsubishi Electric Diamond Contractor

12 Year Parts &
Compressor Warranty

12-year warranty

Extended parts & compressor coverage on qualifying Diamond installations.

Factory-trained crews

Ongoing manufacturer training on the latest hyper-heat systems.

Priority support

Direct factory escalation if anything ever needs attention.

FAQ

Common Questions

Short answers to what Newark homeowners ask before replacing an old furnace and AC.

Do I need to replace my ducts when I get a heat pump?

Not always. We test the existing duct system and compare it to what the new unit needs. Sometimes sealing and fixing returns is enough, and sometimes the trunk lines need replacing.

How do I know what size heat pump my Newark house needs?

A Manual J load calculation. It uses your house’s construction and Newark’s design temperatures. Old systems were often sized by rule of thumb and are bigger than necessary.

Can the heat pump go in the garage?

The indoor unit can, with required clearances and a condensate path. We also check how any gas appliances in the garage are ventilated.

Which agency handles permits in Newark?

The City of Newark’s building division. Replacing equipment and adding circuits generally need permits, and we file them.

Who is my electricity provider, and what about rebates?

PG&E delivers electricity, and Ava Community Energy is the default generation provider for Newark. Incentives from programs like TECH Clean California and BayREN change, and some have eligibility rules. We check availability at the time of your project.

Can you install cooling in my ADU?

Yes. A dedicated mini-split sized to the ADU is the usual approach, and it can run on its own thermostat.

Will it be noisy next to my neighbor’s fence?

Variable-speed outdoor units are quiet at normal operating speeds. We choose the location with the property line and bedroom windows in mind.

Still have a question?

Tell us about your Newark project

Discuss Your Project

Project Inquiry

Ready to Talk Through Your Newark Project?

Tell us what you’re planning. We’ll review the project and follow up with the appropriate next step.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Project category
Project type
Timeline