RESIDENTIAL HVAC · UNION CITY, CA

Residential HVAC & Heat Pumps in Union City, CA

Union City homes range from older Decoto and Alvarado houses to later subdivisions and newer townhome communities near the BART station. We start with how the house is built and what its ducts can actually deliver.

Remodels · Retrofits · Heat Pumps · Multi-Zone Systems

Project Inquiry

Plan your Union City project

Share your project type, ZIP, timeline, and how to reach you. We will follow up.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

  • 5.0 Google Rating 5.0 out of 5 stars
  • Mitsubishi Electric Diamond Contractor
  • C-20 + C-36 Licensed & Bonded
  • Serving the Bay Area since 2015

Sample East Bay project

Whole-home heat pump remodel

View project →
Mitsubishi wall unit in a Berkeley remodel by 3rdGen
Mitsubishi wall unit in a Berkeley remodel by 3rdGen
Mitsubishi hanging outdoor units in a Berkeley remodel by 3rdGen

High-end residential remodel

Hearst Remodel

The Hearst remodel in Berkeley is a published example of how we plan and install a multi-zone heat pump in an older house. It is not a Union City job.

Home type
Existing home, remodel for sale
System
Fujitsu multi-zone ductless heat pump
Mechanical scope
  • · Six indoor wall units
  • · Two outdoor units
  • · Wall-mounted outdoor brackets
  • · Refrigerant routing and field coordination

Challenge

  • Existing older home with limited equipment placement options
  • Outdoor units required side-yard wall bracket mounting
  • Finish-sensitive interior installation
  • Coordination with the general contractor’s remodel schedule

3RDGEN scope

  • Six-zone ductless heat pump installation
  • GC-led remodel coordination
  • Permit and inspection support
  • Startup as part of the completed remodel scope

Outcome

The six-zone Fujitsu ductless system was installed, permitted, inspected, and completed as part of the home’s remodel-for-sale scope — delivering zoned heating and cooling without a conventional ducted retrofit.

Representative example from a Berkeley, CA remodel, not a project in this city. Photos and full details on the project page.

View project

Local projects

Heat pump & HVAC installs for Union City homes

Recent installs by the 3rdGen crew that serves Union City: ducted and ductless heat pumps, air handlers and ductwork.

Horizontal air handler hung in a crawlspace with insulated ductwork and a drain line
Outdoor heat pump condenser mounted beside a louvered vent on the side of a house
Outdoor heat pump condenser mounted on an exterior wall above landscaped planting
Two outdoor condensers on wall brackets with a white line-set cover running down the stucco wall
Sheet-metal plenum and insulated round duct above a furnace in a utility closet
Gas furnace in a finished closet with flue and supply plenum above

Old town to new townhomes

Union City mixes older houses with newer attached housing, and each needs a different plan

The older neighborhoods around Decoto and Alvarado include modest houses with raised floors and original heating. Closer to the BART station and newer developments, townhomes and condos share walls and have limited outdoor space.

Cooling design temperatures here reach the mid 80s, while winter lows are cold enough that a heating-capable system matters. Both ends need to be calculated, not assumed.

Permits for heat pump work are issued by the City of Union City’s building division, and we prepare the supporting load and equipment documents.

  • Raised-floor older homes

    Crawl space ducts are possible when height and moisture allow. When they do not, ductless avoids the problem.

  • Townhome outdoor space

    Small patios and shared walls limit where condensers can go. We verify clearances and HOA rules before choosing a location.

  • Ageing attic systems

    Later homes with attic ducts often have systems sized by habit. A proper load calculation usually brings the size down.

  • Wide temperature swings

    A daily range of about 20 degrees means cool mornings and warm afternoons. Variable-speed equipment handles that better than a fixed-speed unit.

HVAC design in Union City

Union City houses range from raised-floor originals to attached townhomes, and each wants its own system

Union City sits between Hayward and Fremont, with older neighborhoods around Decoto and Alvarado, later single-family subdivisions, and newer townhome communities. The mix means we meet raised floors, attic ducts and tight patios in the same city. A load calculation tells us what each one needs.

Design climate · Title 24 Climate Zone 3
Winter design temp
33°F
Summer design temp
85°F

Union City’s design values are 33°F for heating and 85°F for cooling. Winter nights get cold enough that heating capacity at the design temperature should be checked, while summer afternoons are warm enough to make cooling a real consideration.

ACCA Manual J design data · Union City (micro-climate)

The houses and what they need

Older Union City houses commonly sit on raised floors with wall or floor heaters, and some have had a duct system added later. Insulation levels vary, and so does the condition of the crawl space.

Later single-family homes often have attic duct systems with a furnace in a garage or closet and a matching AC. These are the most straightforward swaps, provided the ducts hold up.

Townhomes and condos tend to have a single-zone system with an outdoor unit on a small patio or balcony. Condenser location and association rules shape the design.

Capacity at 33°F, not just rated tons

Manual S requires checking what a heat pump actually delivers at the heating design temperature. We use manufacturer capacity data at 33°F and compare it to the Manual J heating load.

Crawlspace or ductless?

On older raised-floor homes, a crawlspace duct system works only if there is height and no moisture issue. We measure first. Where ducts will not fit, ductless avoids the problem.

Townhome load and layout

Attached homes have fewer exterior walls, so loads are lower, but stairwells and top floors can still cause uneven comfort. We design airflow for the layout.

Condensate and drain routing

Drain placement is easy to ignore until it fails. We plan the route and termination before installation, including for second-floor air handlers.

Permits, power and incentives in Union City

Heat pump permits in Union City come from the City of Union City’s building division. We send the load calculation, equipment specs and outdoor unit location, and coordinate the inspection.

PG&E delivers electricity, and Ava Community Energy is the default generation provider. Incentives like TECH Clean California and BayREN come and go and may have eligibility conditions, so we verify what is open when we write your proposal.

Where in Union City we work

Decoto, Alvarado, the neighborhoods near the BART station and Union Landing, plus nearby Fremont, Hayward and Newark.

Homeowner reviews

Trusted by Bay Area Homeowners

5.0
5 out of 5 stars from 207 Google reviews

207 Google reviews

  • Mitsubishi Electric outdoor heat pump installed on a concrete pad at a Bay Area home Expand
    Mitsubishi mini-split installed with outstanding care. Indoor and outdoor units done right. High efficiency meant a meaningful federal tax credit too.
    Gary Marks Google review
  • Mitsubishi Electric Smart Multi outdoor unit wall-mounted on a residential exterior Expand
    Devin and his crew did a fantastic job installing AC for our whole house. High quality Mitsubishi equipment and a clean installation throughout.
    Christian Vuerings Google review
  • Mitsubishi Electric air handler installed in an insulated attic with sealed duct connections Expand
    Devin is meticulous, methodical, and knowledgeable. Professional crew and a heat pump install we trust completely.
    D C Google review

Photos from the installs above

Read all 207 reviews

Project steps

How we deliver a Union City system

Each step answers a specific question: what does the house need, what equipment matches, how does air get there, and how do we prove it works.

01 — Intake and site visit

Goals, house age, current heating and cooling, electrical panel and any plans for additions.

02 — Manual J

We calculate the load room by room, with attention to windows, insulation and orientation.

03 — Manual S

Equipment is selected from manufacturer data to match the load at Union City design temperatures.

04 — Manual D and permitting

Duct or line-set layout is finalized and the permit package goes to the City.

05 — Installation

Equipment, ducts or line sets, wiring and drain are installed to the design.

06 — Startup and walkthrough

Charge, airflow and controls are verified, and the inspector signs off before we hand over.

Beyond the equipment

What a Union City conversion usually includes

Removing a furnace or wall heater leaves gas lines, vents and openings that need to be closed properly. New equipment needs power, a drain and a place to sit.

We take care of all of that and then test the system.

Tell us about the project
  • Decommission old heat

    Gas capped, flue removed and openings patched.

  • Distribution

    Ducts repaired or lines installed to match the design.

  • Electrical and drain

    Circuit, disconnect and condensate path installed.

  • Verification

    Airflow, refrigerant charge and controls verified before we leave.

Cost

What goes into the price of a Union City heat pump job

The mix of ducts, zones, electrical work and equipment access varies widely. A swap with sound ducts is a smaller scope than a conversion that needs new distribution or a panel upgrade.

Ducted heat pump, existing ducts usable $20k–$30k Equipment tier, capacity, controls, condenser location and access
Ducted heat pump + duct repair or resizing $25k–$45k Amount of ductwork replaced, crawlspace or attic access, return-air changes
Ductless multi-zone, 3–4 heads $25k–$40k Head type, line-set length, routing, concealment and finish conditions
Whole-home ducted + ductless combination $40k–$80k+ Multiple systems, zoning, ductwork, filtration, ventilation and architectural coordination
New construction system $20k–$50k+ Building size, system count, Title 24/design requirements and coordination with the build
ADU system $10k–$15k Zone count, head type, line-set routing, and whether the ADU shares the main house or stands alone
Electrical panel upgrade, when required $10k+ Service size, meter location, utility requirements and site conditions

Prices as of November 2026. Complex whole-home and design-build projects can exceed these ranges. Rebates and incentives may reduce your net project cost.

Project inquiry

Start a Union City HVAC conversation

Share your house type, the heating and cooling you have now, and any changes you are planning. A project lead will respond.

  • Reviewed by a project lead, not a dispatcher
  • We tell you if your scope is not a fit for us
  • No high-pressure in-home sales appointment

Project Inquiry

Send your project details

Project type, ZIP, timeline, and how to reach you.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Mitsubishi Electric

Proud Mitsubishi Electric Diamond Contractor

As a Mitsubishi Electric Diamond Contractor, we design and install ducted, ductless, and multi-zone systems for Bay Area homes, with factory-trained crews and longer warranty options on qualifying residential installs.

Mitsubishi is not automatically the answer to every home. We start with what the project requires and recommend the system that makes sense.

Mitsubishi Electric H2i hyper-heat outdoor heat pump units
Mitsubishi Electric Heating and Air Conditioning Mitsubishi Electric Diamond Contractor

12 Year Parts &
Compressor Warranty

12-year warranty

Extended parts & compressor coverage on qualifying Diamond installations.

Factory-trained crews

Ongoing manufacturer training on the latest hyper-heat systems.

Priority support

Direct factory escalation if anything ever needs attention.

FAQ

Common Questions

What Union City homeowners usually want to know about ducts, permits, power and comfort.

What is the difference between ducted and ductless for an older Union City home?

Ducted spreads air through registers and needs room for ducts. Ductless uses wall or ceiling heads and needs only small refrigerant lines. Houses with no good duct space usually suit ductless better.

Does a heat pump work through a Union City winter?

Yes. Winter design temperature here is in the low 30s°F, and modern heat pumps deliver full rated heating capacity well below that. We confirm capacity at the design temperature during equipment selection.

Who handles permits in Union City?

The City of Union City’s building division. A heat pump replacement needs a mechanical permit, and often an electrical permit. We handle the paperwork and inspections.

Who provides power and are there incentives?

PG&E delivers electricity, and Ava Community Energy is the default generation provider in Union City. Incentives such as TECH Clean California and BayREN change, so we check what is available and whether you qualify.

I live in a townhome. Can I switch to a heat pump?

Often yes. We check your HOA rules, available condenser locations and the drain path, then size the system to your unit.

One room is always hot or cold. Will a new system fix it?

It can, if the duct design is part of the fix. We measure the room load and compare it with the airflow it gets today.

Do I need a new electrical panel?

Sometimes. We calculate whether your existing service can carry the heat pump and any other planned loads, and recommend an upgrade only if needed.

Still have a question?

Tell us about your Union City project

Discuss Your Project

Project Inquiry

Ready to Talk Through Your Union City Project?

Tell us what you’re planning. We’ll review the project and follow up with the appropriate next step.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Project category
Project type
Timeline