RESIDENTIAL HVAC · CORTE MADERA, CA

Residential HVAC & Heat Pumps in Corte Madera, CA

Low attics, damp crawlspaces and bright afternoon sun define Corte Madera houses. We design heat pump systems that deal with each one, based on a Manual J of your home.

Remodels · Retrofits · Heat Pumps · Multi-Zone Systems

Project Inquiry

Plan your Corte Madera project

Share your project type, ZIP, timeline, and how to reach you. We will follow up.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

  • 5.0 Google Rating 5.0 out of 5 stars
  • Mitsubishi Electric Diamond Contractor
  • C-20 + C-36 Licensed & Bonded
  • Serving the Bay Area since 2015

Recent Corte Madera project

Two-zone ducted heat pump with ERV

View project →
Ducted air handler installed under the floor

Full-System Residential Retrofit

Blue Rock Ct, Corte Madera

This Corte Madera home had a furnace on the top floor. In early 2024 we removed it and installed two Mitsubishi 1.5-ton ducted heat pumps in the crawlspace, one for each floor, with new returns, new plenums and rerouted supply duct. A Panasonic ERV in the crawlspace now supplies fresh air to both zones. In 2026 the owner had us back to reroute and extend a return in rigid duct.

Client
Residential homeowner
System
Two Mitsubishi 1.5-ton ducted heat pumps with a Panasonic ERV
Mechanical scope
  • · Removed the top-floor furnace
  • · Two Mitsubishi SVZ-KP18NA air handlers on unistrut with vibration pads in the crawlspace
  • · Two SUZ-KA18NA2 outdoor units on wall mounts
  • · New returns, including a 20x24 return for the lower floor, with 16 in R-8 flex to the return plenums
  • · Supply and return plenums with damper take-offs; supply duct rerouted in R-8 flex

Challenge

  • All air handlers and the ERV fit into the crawlspace
  • Two floors served by separate zones

3RDGEN scope

  • 3rdGen designed the two-zone layout and ventilation, installed both systems and the ERV, and returned in 2026 to rework a return.

Outcome

Each floor has its own heat pump and thermostat, and both get continuous fresh air from the ERV. As a Mitsubishi Diamond Contractor install, the equipment carries Mitsubishi's 10-year warranty plus 2 extra years.

Completed 2024 in Corte Madera. Photos and full details on the project page.

View project

Local projects

Heat pump & HVAC installs for Corte Madera homes

Recent installs by the 3rdGen crew that serves Corte Madera: ducted and ductless heat pumps, air handlers and ductwork.

Gas furnace in a finished closet with flue and supply plenum above
Gas furnace with flexible gas connector and shutoff valve beside it in a closet
Floor-standing fan coil unit installed along the wall of a freshly painted room
Round sheet-metal duct turning into a wall in a finished utility space
Wall-mounted ductless indoor unit above a seating area in a finished living room
Large two-fan heat pump condenser on a gray pad against house siding

Flats and hillsides

Two kinds of Corte Madera lot, two kinds of heat pump plan

On the flat, low-lying side, the concerns are shallow crawlspaces, moisture and where water can collect around an outdoor unit. On the hill, they are stairs, slope and tight yards.

Most homes were built between the 1950s and 1970s with low attics. Ducts that were crammed in then rarely suit a heat pump’s airflow, so we redesign them instead of copying them.

The design summer is about 88°F and the winter low is about 35°F, with a big daily swing. A variable-speed heat pump handles both ends, cooling a hot afternoon and gently holding a cold night.

  • Low attics

    Compact air handlers and short trunks replace bulky legacy runs.

  • Crawlspace moisture

    We specify sealed, insulated runs and clean condensate paths.

  • West sun

    Afternoon solar gain drives cooling loads, so we model it carefully.

  • Raised outdoor units

    Where water can pool, units go on stands with electrical connections held high.

HVAC design in Corte Madera

Corte Madera homes sit on flat bayside lots and wooded hillsides, and the heat pump plan changes between them

Corte Madera is small but varied. Low-lying neighborhoods near the bay deal with damp ground and flood awareness. Streets climbing toward the ridge deal with slope, trees and stairs. We design each house on its own load and site, not from a template.

Design climate · Title 24 Climate Zone 2
Winter design temp
35°F
Summer design temp
88°F

The Manual J numbers for Corte Madera are about 35°F heating and 88°F cooling, with a daily range near 34°F. Hot, bright afternoons and chilly nights mean a variable-speed system that can both cool a sun-baked room and gently hold overnight heat.

ACCA Manual J design data · Corte Madera (ACCA micro-climate)

Housing we see in Corte Madera

Many homes were built in the 1950s through the 1970s: single-story ranches and split-levels with low attics, slab or raised foundations, and older gas furnaces.

Flat, low-lying lots can have shallow crawlspaces and moisture issues, which matters when ducts or condensate lines run underneath. Hillside properties have limited yard space and steps between the street and front door.

Townhomes and condo complexes are part of the mix, with their own rules for where an outdoor unit can go.

Low attics, tight chases

Ranch homes often have only a foot or two of attic clearance. Manual D guides us to compact air handlers, short trunk runs and low-profile registers instead of bulky legacy duct layouts.

Moisture and crawlspace ducts

Where ducts run in a damp crawlspace, we specify sealed, insulated runs and proper condensate drainage. Sometimes the better call is to move ducts into the attic or choose ductless heads.

Manual J for bright afternoons

West windows and flat roofs drive afternoon load in many Corte Madera houses. We model solar gain carefully and sometimes suggest window film or shading to reduce the tonnage needed.

Elevated outdoor units

In areas where water can pool, we raise outdoor units off the ground and keep electrical connections high.

  • Ranch-home heat pump conversions

    Ducted conversion of single-story homes from gas furnace and AC to a single heat pump system.

    Replacement & conversion →
  • Ductless additions and bonus rooms

    Zoned heads for garage conversions, sunrooms or additions the old system never served.

    Heat pump installation →
  • Manual J load reports

    A clear load and equipment package for the system we install, ready for permits and remodel plans.

    Manual J load calculations →
  • Remodel-stage HVAC

    Mechanical design while walls are open, so ducts and lines are hidden and sized correctly.

    HVAC for remodels →
  • ADU heating and cooling

    Properly sized mini-splits with their own thermostat for backyard or garage units.

    ADU heating & cooling →

Permits, MCE and incentives in Corte Madera

The Town of Corte Madera’s Building Division reviews mechanical, electrical and energy-code compliance for heat pump work. We prepare the load report, equipment data and a simple site drawing with the outdoor unit location, and we pull the permit.

Your power is generated by MCE by default and delivered by PG&E. Incentive programs from TECH Clean California, BayREN and utilities change over time, so we confirm what is open when we quote. Our rebates page explains the general landscape.

Where we work around Corte Madera

Flat neighborhoods near the bay, hillside streets toward the ridge and the area around the town center, plus Larkspur, Mill Valley, Tiburon and San Anselmo.

Homeowner reviews

Trusted by Bay Area Homeowners

5.0
5 out of 5 stars from 207 Google reviews

207 Google reviews

  • Mitsubishi Electric outdoor heat pump installed on a concrete pad at a Bay Area home Expand
    Mitsubishi mini-split installed with outstanding care. Indoor and outdoor units done right. High efficiency meant a meaningful federal tax credit too.
    Gary Marks Google review
  • Mitsubishi Electric Smart Multi outdoor unit wall-mounted on a residential exterior Expand
    Devin and his crew did a fantastic job installing AC for our whole house. High quality Mitsubishi equipment and a clean installation throughout.
    Christian Vuerings Google review
  • Mitsubishi Electric air handler installed in an insulated attic with sealed duct connections Expand
    Devin is meticulous, methodical, and knowledgeable. Professional crew and a heat pump install we trust completely.
    D C Google review

Photos from the installs above

Read all 207 reviews

Project steps

What a Corte Madera heat pump project looks like

Low attics and damp crawlspaces leave little room for error, so the design steps come before the order is placed.

01 — Attic and crawlspace look

We check the clearances, the duct condition, any moisture and your service panel.

02 — Manual J

Load calculated with special attention to sun exposure and ceiling insulation.

03 — Manual S and D

Equipment to the load, with compact duct layouts drawn to fit the available space.

04 — Town permit

Building Division package with load report, equipment data and a site plan.

05 — Installation

Old system removed, ducts and lines installed, outdoor unit elevated and wired.

06 — Startup

Airflow, charge and controls tested, inspection closed, walkthrough with you.

From plan to handoff

The pieces of a Corte Madera install

We handle indoor and outdoor equipment, ducts, drains, electrical and permit in one coordinated scope.

After startup we test airflow and show you how to use zones and schedules.

Tell us about the project
  • Permit and plan

    Load report and site layout submitted for permit.

  • Duct or line routing

    Compact runs through attic or crawlspace, sealed and insulated.

  • Outdoor pad

    Elevated or bracketed unit with condensate handled.

  • Commissioning

    Charge, airflow and controls verified.

Cost

Corte Madera pricing: what moves the number

A house with a roomy attic and sound ducts costs less than one with a damp crawlspace or a tight attic that needs rerouting. Zones, line set length, outdoor unit mounting and electrical work are the main variables.

Ducted heat pump, existing ducts usable $20k–$30k Equipment tier, capacity, controls, condenser location and access
Ducted heat pump + duct repair or resizing $25k–$45k Amount of ductwork replaced, crawlspace or attic access, return-air changes
Ductless multi-zone, 3–4 heads $25k–$40k Head type, line-set length, routing, concealment and finish conditions
Whole-home ducted + ductless combination $40k–$80k+ Multiple systems, zoning, ductwork, filtration, ventilation and architectural coordination
New construction system $20k–$50k+ Building size, system count, Title 24/design requirements and coordination with the build
ADU system $10k–$15k Zone count, head type, line-set routing, and whether the ADU shares the main house or stands alone
Electrical panel upgrade, when required $10k+ Service size, meter location, utility requirements and site conditions

Prices as of November 2026. Complex whole-home and design-build projects can exceed these ranges. Rebates and incentives may reduce your net project cost.

Project inquiry

Send us your Corte Madera project

Tell us whether you are on the flat or the hill, what heats the house now and what you want improved.

  • Reviewed by a project lead, not a dispatcher
  • We tell you if your scope is not a fit for us
  • No high-pressure in-home sales appointment

Project Inquiry

Send your project details

Project type, ZIP, timeline, and how to reach you.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Mitsubishi Electric

Proud Mitsubishi Electric Diamond Contractor

As a Mitsubishi Electric Diamond Contractor, we design and install ducted, ductless, and multi-zone systems for Bay Area homes, with factory-trained crews and longer warranty options on qualifying residential installs.

Mitsubishi is not automatically the answer to every home. We start with what the project requires and recommend the system that makes sense.

Mitsubishi Electric H2i hyper-heat outdoor heat pump units
Mitsubishi Electric Heating and Air Conditioning Mitsubishi Electric Diamond Contractor

12 Year Parts &
Compressor Warranty

12-year warranty

Extended parts & compressor coverage on qualifying Diamond installations.

Factory-trained crews

Ongoing manufacturer training on the latest hyper-heat systems.

Priority support

Direct factory escalation if anything ever needs attention.

FAQ

Common Questions

Corte Madera answers on low attics, moisture, sun and permits.

My ranch house has a very low attic. Can a heat pump still be ducted?

Often. Compact air handlers, short trunks and low-profile registers work in tight spaces. If clearance is too small, ductless heads in the main rooms are a clean alternative.

What about ducts in a damp crawlspace?

We look for moisture first. Sealed, insulated runs with proper drainage can work. If conditions are poor, moving ducts to the attic or using ductless heads avoids the issue.

Is a heat pump enough for Corte Madera afternoons?

Yes. The design cooling temperature is about 88°F. A properly sized variable-speed unit covers that and still runs quietly on mild days.

Does the town permit heat pump installs?

Yes. The Town’s Building Division reviews the mechanical work. We prepare the documents and pull the permit.

Who is my power provider?

MCE provides generation by default and PG&E delivers it. Incentives from TECH Clean California, BayREN and utilities change over time, so we verify what is available when we quote.

Can the outdoor unit sit in a low area?

We would rather raise it. In low-lying spots we mount units on stands and keep electrical connections high.

Can you add HVAC to a converted garage?

Yes. A ductless head or two, sized to the room’s load, usually works well and does not require duct work.

Still have a question?

Tell us about your Corte Madera project

Discuss Your Project

Project Inquiry

Ready to Talk Through Your Corte Madera Project?

Tell us what you’re planning. We’ll review the project and follow up with the appropriate next step.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Project category
Project type
Timeline