RESIDENTIAL HVAC · ROSS, CA

Residential HVAC & Heat Pumps in Ross, CA

Big lots, mature trees and houses that grew by additions. We divide a Ross home into real thermal zones, calculate each one, and install heat pump systems that serve the whole house evenly.

Remodels · Retrofits · Heat Pumps · Multi-Zone Systems

Project Inquiry

Plan your Ross project

Share your project type, ZIP, timeline, and how to reach you. We will follow up.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

  • 5.0 Google Rating 5.0 out of 5 stars
  • Mitsubishi Electric Diamond Contractor
  • C-20 + C-36 Licensed & Bonded
  • Serving the Bay Area since 2015

Published multi-zone example

Whole-home heat pump remodel

View project →
Mitsubishi wall unit in a Berkeley remodel by 3rdGen
Mitsubishi wall unit in a Berkeley remodel by 3rdGen
Mitsubishi hanging outdoor units in a Berkeley remodel by 3rdGen

High-end residential remodel

Hearst Remodel

A Berkeley remodel with six indoor units and two outdoor units, included to show how we document and coordinate a multi-zone scope. It is not a Ross address.

Home type
Existing home, remodel for sale
System
Fujitsu multi-zone ductless heat pump
Mechanical scope
  • · Six indoor wall units
  • · Two outdoor units
  • · Wall-mounted outdoor brackets
  • · Refrigerant routing and field coordination

Challenge

  • Existing older home with limited equipment placement options
  • Outdoor units required side-yard wall bracket mounting
  • Finish-sensitive interior installation
  • Coordination with the general contractor’s remodel schedule

3RDGEN scope

  • Six-zone ductless heat pump installation
  • GC-led remodel coordination
  • Permit and inspection support
  • Startup as part of the completed remodel scope

Outcome

The six-zone Fujitsu ductless system was installed, permitted, inspected, and completed as part of the home’s remodel-for-sale scope — delivering zoned heating and cooling without a conventional ducted retrofit.

Representative example from a Berkeley, CA remodel, not a project in this city. Photos and full details on the project page.

View project

Local projects

Heat pump & HVAC installs for Ross homes

Recent installs by the 3rdGen crew that serves Ross: ducted and ductless heat pumps, air handlers and ductwork.

Ductless heat pump condenser mounted on a pad beside a gray house with a neat line set
Air handler in an attic with insulated flex duct and a neat white condensate drain
Vertical air handler in a closet with condensate drain and ductwork
Wall-mounted ductless indoor unit on a clean gray wall
Heat pump condenser mounted on a pad against a stucco wall
Two-fan heat pump condenser installed in a narrow side yard

DECADES OF ADDITIONS

A Ross house is usually several buildings stitched together, and HVAC has to treat it that way

A 1920s core, a later addition and a converted lower level have different insulation, windows and exposures. One thermostat cannot serve all of them, so we calculate each area and group them into zones.

ACCA has no Ross listing, so we use nearby San Anselmo: about 33°F winter and 86°F summer design. Ross sits in a shaded valley, but we still design to the published numbers.

Mechanical permits go through the Town’s Building Department. Larger projects may also need the Town’s design review, and steep lots have additional hillside review. We coordinate unit placement with your design team early.

  • Mixed construction eras

    Separate loads for the original house, additions and lower levels keep each zone right-sized.

  • Finished interiors

    Plaster ceilings, millwork and built-ins limit duct paths, so we plan chases early.

  • Trees and leaf litter

    Outdoor units need clearance and a service path in shaded, leafy yards.

  • Creek-side lots

    Where flooding has occurred, we raise outdoor equipment and electrical connections.

HVAC design in Ross

Large, older Ross houses need a heat pump designed zone by zone

Ross is a small, wooded town of larger lots and established homes, many with additions layered over decades. One thermostat rarely serves a house like that. We split the building into zones, calculate each one, and pick equipment that fits the architecture as well as the load.

Design climate · Title 24 Climate Zone 2
Winter design temp
33°F
Summer design temp
86°F

ACCA has no Ross entry, so we use neighboring San Anselmo: about 33°F heating and 86°F cooling. Ross is tucked into a tree-covered valley, so the actual conditions can feel cooler in the shade than those numbers suggest, but we design to the published values.

ACCA Manual J design data · San Anselmo (nearest ACCA station; no Ross listing)

What Ross houses look like mechanically

Many Ross homes are larger, older properties with multiple wings, finished lower levels, and rooms added at different times. Each addition often has its own insulation level and its own old heating equipment.

Mature trees shade a lot of the town, which reduces cooling loads on some sides but also drops debris on outdoor units and covers roofs and decks that will hold equipment.

Lots near Corte Madera Creek can have flood concerns, and outdoor equipment should be placed with that history in mind.

Zone the house the way it was built

A 1920s core plus a 1980s addition plus a converted basement are three different thermal spaces. Manual J on each tells us where one ducted system fits and where a separate zone or ductless head is cleaner.

Manual S for estates

Larger homes do not always need large tonnage. When envelopes have been updated, loads can be surprisingly small. We pick multiple smaller units over a single oversized one when it keeps each zone comfortable.

Duct design around finished spaces

Plaster ceilings, built-in cabinetry and finished attics limit where new ducts can run. Manual D work here focuses on finding chases and using slim ducted fan coils.

Shade, leaves and service access

Outdoor units in tree cover need clearance from leaf litter and a service path. We place them where a technician can reach them and airflow stays unobstructed.

  • Multi-system design for large homes

    Two or more heat pump systems or zoned equipment sized to separate wings and floors.

    Heat pump installation →
  • Full gas-to-electric conversion

    Replace boilers, furnaces and AC across the house with heat pumps, with panel and gas scope included.

    Replacement & conversion →
  • HVAC for architect-led projects

    Mechanical planning that works with ceilings, cabinetry and the design team’s drawings.

    HVAC for remodels →
  • New construction and rebuilds

    Load calcs, equipment layout and duct design for a ground-up house.

    HVAC for new construction →
  • Whole-house ventilation

    ERV and filtration design for tighter, renovated homes and smoky seasons.

    Ventilation & IAQ →
  • Manual J, S and D documents

    Plan-ready calculations for your architect, builder or the building department.

    Manual J load calculations →

Ross permits, MCE and rebates

Mechanical permits go through the Town of Ross Building Department. Larger projects can also involve the Town’s design review, and hillside properties have their own review rules, so we coordinate equipment locations with your design team early.

MCE is the default generation provider for Ross, with PG&E delivering the power. TECH Clean California, BayREN and utility incentives change, so we verify what is open before pricing. See our rebates page for how the programs work.

Where we work around Ross

The Ross Common area, valley and hillside streets, plus Kentfield, San Anselmo, Larkspur and Greenbrae.

Homeowner reviews

Trusted by Bay Area Homeowners

5.0
5 out of 5 stars from 207 Google reviews

207 Google reviews

  • Mitsubishi Electric outdoor heat pump installed on a concrete pad at a Bay Area home Expand
    Mitsubishi mini-split installed with outstanding care. Indoor and outdoor units done right. High efficiency meant a meaningful federal tax credit too.
    Gary Marks Google review
  • Mitsubishi Electric Smart Multi outdoor unit wall-mounted on a residential exterior Expand
    Devin and his crew did a fantastic job installing AC for our whole house. High quality Mitsubishi equipment and a clean installation throughout.
    Christian Vuerings Google review
  • Mitsubishi Electric air handler installed in an insulated attic with sealed duct connections Expand
    Devin is meticulous, methodical, and knowledgeable. Professional crew and a heat pump install we trust completely.
    D C Google review

Photos from the installs above

Read all 207 reviews

Process

How we deliver a Ross project

Large homes need more steps and more coordination. Each stage below ends with something you can review.

01 — Zone mapping

We walk the whole house and mark where construction era, exposure and use change.

02 — Manual J per zone

Separate heating and cooling loads for each zone, using real envelope data.

03 — Manual S and D

Equipment selected for each zone and ducts drawn around finished ceilings and built-ins.

04 — Design review and permit

Equipment locations coordinated with your architect and the Town’s review requirements, then permit.

05 — Staged installation

Rough-in wing by wing, equipment set and electrical upgraded as required.

06 — Zone commissioning

Each zone tested and tuned, then controls explained and the inspection completed.

Large-house delivery

Delivering a multi-zone Ross project

On a large home, sequence matters. We stage rough-in by wing so you can stay in the house where possible.

Every zone is commissioned separately and documented.

Tell us about the project
  • Zone-by-zone rough-in

    Ducts and lines routed wing by wing.

  • Equipment placement

    Indoor and outdoor units set with access and clearance.

  • Electrical upgrades

    Panel and sub-panel capacity added as needed.

  • Zone commissioning

    Each zone tested and tuned, then handed off with controls explained.

Cost

What shapes the price of a Ross HVAC project

Ross pricing depends on how many zones the house needs, how hard it is to hide ducts, how much electrical work is required and how much coordination the design team asks for. Square footage alone is a poor guide.

Ducted heat pump, existing ducts usable $20k–$30k Equipment tier, capacity, controls, condenser location and access
Ducted heat pump + duct repair or resizing $25k–$45k Amount of ductwork replaced, crawlspace or attic access, return-air changes
Ductless multi-zone, 3–4 heads $25k–$40k Head type, line-set length, routing, concealment and finish conditions
Whole-home ducted + ductless combination $40k–$80k+ Multiple systems, zoning, ductwork, filtration, ventilation and architectural coordination
New construction system $20k–$50k+ Building size, system count, Title 24/design requirements and coordination with the build
ADU system $10k–$15k Zone count, head type, line-set routing, and whether the ADU shares the main house or stands alone
Electrical panel upgrade, when required $10k+ Service size, meter location, utility requirements and site conditions

Prices as of November 2026. Complex whole-home and design-build projects can exceed these ranges. Rebates and incentives may reduce your net project cost.

Project inquiry

Start your Ross HVAC project

Send the house layout, additions history, design team and timeline.

  • Reviewed by a project lead, not a dispatcher
  • We tell you if your scope is not a fit for us
  • No high-pressure in-home sales appointment

Project Inquiry

Send your project details

Project type, ZIP, timeline, and how to reach you.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Project teams

Designed with the people who design the house

Mechanical choices are easiest to make before cabinets and ceilings are drawn. We work with architects and builders so equipment, chases and service access are built into the plan.

We work within existing project teams in Ross and across Marin — or directly with homeowners when that is the right path.

Mitsubishi Electric

Proud Mitsubishi Electric Diamond Contractor

As a Mitsubishi Electric Diamond Contractor, we design and install ducted, ductless, and multi-zone systems for Bay Area homes, with factory-trained crews and longer warranty options on qualifying residential installs.

Mitsubishi is not automatically the answer to every home. We start with what the project requires and recommend the system that makes sense.

Mitsubishi Electric H2i hyper-heat outdoor heat pump units
Mitsubishi Electric Heating and Air Conditioning Mitsubishi Electric Diamond Contractor

12 Year Parts &
Compressor Warranty

12-year warranty

Extended parts & compressor coverage on qualifying Diamond installations.

Factory-trained crews

Ongoing manufacturer training on the latest hyper-heat systems.

Priority support

Direct factory escalation if anything ever needs attention.

FAQ

Common Questions

Ross answers about zoning, finished interiors, creeks and review.

Why does my Ross house need more than one system?

Additions, lower levels and different eras of construction heat and cool differently. Separate zones or systems, each sized to its own load, deliver more even comfort than one big unit.

Can ducts be added without damaging plaster ceilings?

Sometimes. We look for closets, attic spaces, floor cavities and existing chases first. Where none exist, ductless heads or slim ceiling units avoid cutting finished surfaces.

What design temperatures do you use for Ross?

ACCA lists no Ross station, so we use San Anselmo: about 33°F winter and 86°F summer. We verify equipment capacity at both conditions.

Will the Town review my outdoor equipment?

Mechanical work needs a permit through the Town’s Building Department. Larger projects can also trigger design review, and steep sites have hillside review. We show equipment locations on plans from the beginning.

My lot is near the creek. Does that change anything?

It can. We raise outdoor units on stands and keep electrical connections above likely water levels where flooding has been an issue.

Who provides my electricity?

MCE supplies generation by default and PG&E delivers it. Heat pump incentives from TECH Clean California, BayREN and utility programs change over time, so we confirm what is open when we scope the work.

Will I need a panel or sub-panel upgrade?

Large homes converting from gas to electric often do. We total the loads for heat pumps and other electrification before the design is final.

Still have a question?

Tell us about your Ross project

Discuss Your Project

Project Inquiry

Planning HVAC for a Ross home?

Tell us about the house, any additions, who is on the design team and when work starts. Plans or a floor layout help us scope zones. We reply if the project is a fit.

We design and install complete systems in the East Bay, San Francisco and Marin. We do not do repair, service calls or maintenance.

Project category
Project type
Timeline